What’s in the box?
Wand
Valve Handle
Unit
Hose
Handle
What are the parts of the HD101?
The HD101 has a variety of high-quality parts that combine to make an excellent sprayer for your lawn, gardening, and growing needs.
Tank
The translucent, 1-gallon container that holds a variety of liquid solutions. It has a wide-mouth lid for easy filling and easy-to-read liquid measurement lines.
Valve Handle
The mechanism that activates the pump and starts the spray. It’s a sturdy, lightweight handle that’s large enough for anyone to hold comfortably.
Pressure Release Valve
Safeguards against over-pressurization by automatically releasing excess pressure from the tank, protecting the sprayer from damage.
Wand with Nozzle Attachment
This wand comes with 2 nozzles that can be used for all types of solutions from a fine mist to a steady stream spray.
Hose
Flexible and sturdy with a generous length, the black hose ensures an easy spray that covers hard-to-reach areas, from lawn care to misting delicate plants.
How to use the HD101
Learn how to effortlessly operate the HD101 with our easy-to-follow user guide.
Step 1
The hose comes attached to the side of the sprayer.
Step 2
The valve handle comes attached to the other end of the hose.
Step 3
Thread the wand to the end of the valve handle.
Step 4
Attach your nozzle of choice.
Step 5
After pouring your chosen liquid into the tank, pump the handle to build pressure.
Step 6
Use the trigger to spray. Remember to avoid bleaches, acids, and thick/creamy substances.
Step 7
Apply plumber’s tape to any threading for leak prevention.
Step 8
Always pull the pressure release valve when you are done using the sprayer.
Troubleshooting your HD101 Pump sprayer
Don't let a malfunctioning sprayer keep you from your gardening chores - use our troubleshooting guide to fix common problems with the HD101 Pump Sprayer.
Check your tank
Make sure the tank is properly sealed and tightened to prevent air leaks. Remember to pump the handle several times before use to build up pressure in the tank.
Inspect the nozzle
If the spray is not coming out of the nozzle or the spray pattern is not as expected, inspect the nozzle for blockages or damage. Unscrew the nozzle and clean it thoroughly with water to remove any dirt or debris. If the nozzle appears damaged, replace it with a new one.
Check for leaks
Double check all connections to ensure they are tight and not leaking. Replace any damaged or worn parts as needed.
Check the spray solution
Make sure the spray solution is mixed properly and not too thick. Adjust the mixture as needed to ensure proper flow and spray pattern.
How To Clean your Sprayer
Maintaining a clean HD101 Pump Sprayer will keep it in good working order. Here's how:
Step 1
Empty any remaining solution from the tank and rinse it thoroughly with clean water.
Step 2
Fill the tank with a cleaning solution, such as water and vinegar or soap and water.
Step 3
Pump the sprayer to circulate the cleaning solution through the hose and nozzle.
Step 4
Pump the sprayer to circulate the cleaning solution through the hose and nozzle.
Step 5
Rinse the tank, hose, and nozzle with clean water and spray this through the sprayer to flush out any remaining residue.
Step 6
Let the sprayer air-dry, and store it in a cool, dry place.
How To Prime the Pump
Priming your HD101 Pump Sprayer is simple. Just follow these two steps:
Step 1
Add 1 gallon of warm soapy water into the tank. Make sure that you use warm water and that you are adding the right amount of soap. Ideally, 1-2 teaspoons of liquid soap per gallon of water.
Step 2
Close the lid, pump the unit, then spray. Make sure that you have tightly closed the lid. Depending on what's causing the issue, you could have flow coming out of the hose in a couple of minutes.
How To Prepare your Sprayer for Winter Storage
Before you put your sprayer away for the winter, there are a few things you should do to make sure it’s in good shape for next season.
Step 1
Run 1 gallon of warm water mixed with 2 teaspoons of liquid dish soap through the unit to clean all internal parts, then run 1 more gallon of warm water only through. Spray until the unit, wand & hose are fully empty.
Step 2
Place the unit right-side-up in the warmest storage possible. Do not store long-term in temps below 32°F.
Step 3
Place the unit right-side-up in the warmest storage possible. Do not store long-term in temps below 32°F.
Conclusion
We hope this troubleshooting guide has helped you address any issues you may have encountered with your HD101 Pump Sprayer. Thank you for choosing the HD101 pump sprayer, and happy spraying!
Join our gold club
Become a member of our Gold Club and get exclusive benefits only available to Members like extended warranties, free products, community access and more.
Explore furtherFREQUENTLY ASKED QUESTIONS
HOW DO I CONTACT YOU?
Our customer success team can be reached at 1-800-613-6889; 7 days a week.
Monday-Friday: 8 AM-8 PM EST
Saturday & Sunday: 9 AM-5 PM EST, or reach out to us via email at support@petratools.com
You agree to receive follow-up text messages and calls by calling or texting this number. If you no longer wish to receive text messages or calls, you may opt-out at any time by replying "STOP"
HOW LONG DOES IT TAKE TO DELIVER?
Orders typically ship within 2 business days and arrive 3-5 days after shipment.
WHERE ARE YOU LOCATED?
We are located in central Pennsylvania.
IS THERE A WARRANTY ON EACH ITEM?
PetraTools provides a standard 3-month full warranty for manufacturer defects. If customer registers for extended warranty, PetraTools provides an additional 3 months limited warranty. Limited warranty covers replacement units due to manufacturer defects (shipping paid by customer).
PetraTools sprayers are available for free returns for 30 days post-purchase. All other chemicals and solutions are not eligible for returns or exchanges at this time. Please contact Customer Service if you have received a damaged product so we can replace it for you.
Otherwise, we ask that you be kind to our planet and share any unwanted orders with a neighbor or friend.